Sunroom Exterior Walls

A real, actual post! Yes, I know it's been ages. I stopped working on the house a few years ago because I accepted a new position at work that requires me to travel a lot. Oh, and we've also had 3 kids in 4 years. I am now in between projects that require travel so I figured that now is a good time to get back to work on the house and try to finish it up.

The project I chose to start on is the exterior of the sunroom. I never finished the exterior walls when I built the sunroom, a combination of white pine trim boards with no paint, only primer on some of them, and a major design flaw, caused a lot of rot.

The bottom exterior trim board ended up sandwiched in with the deck ledger board, creating a pocket to hold, moisture and leaves.

The area circled is where the moisture and leaves would collect. You can see all the rot.

I removed all the rotted boards and put up new plywood.

This time around I decided to use siding instead of paneling. I added siding to the bottom and top areas, and installed new trim boards where they were needed. There is now a small gap between the siding and the edge of the deck for water to shed off.

I then caulked all the seams and began primering the trim.

Most of the trim has been primered. Tomorrow I will finish primering the trim and the siding and then I can paint everything to match the house.

I will tackle the windows at a later time. I will have to remove one at a time, strip them down completely, primer, paint, reinstall glass and glaze. Not really looking forward to that part.

Researching for Historical Accuracy - picket fences

Historical Accuracy is very important to me in restoring my house. So when JC posted a comment about my picket fence being historically accurate I decided to make a post on the research I did before building my fence.

Over the years I've seen numerous old house photos and one one of the things I noticed was that most houses that had picket fences used 1x1 square pickets instead of board pickets.

Here is a picture of a house here in Woodbury that was taken in 1908. At the right of the picture is a square picket fence.

 1908, Woodbury, Ga

Another thing I noticed was that a lot of these fences had alternating height pickets. I wanted to do something that would stand out a little so this seemed perfect.

Here are some pictures of alternating height square picket fences that I found while doing my research.

 Undated, Bryan Co, Ga

 1914, Columbia Co, Ga

 1905, Decatur Co, Ga

 1890, Dekalb Co, Ga

 1909, Emanuel Co, Ga

 Undated, Franklin Co, Ga

 1898, Hancock Co, Ga

 1895, Montgomery Co, Ga

1870-1899, Schley Co, Ga

Every one of the pictures above has the alternating height, square pickets. Also, all the pictures are in the same time-frame of my house.

The one major difference in these fences and mine is the board that runs along the bottom in all of the others. I may add this board to my fence, I haven't decided yet.

Picket Fence

What started out as a quick trim-up of the bushes turned into a huge project.

The hedge I was trimming is the Boxwood hedge on the north side of the house, it has gotten extremely overgrown. Not to mention the 18' Oak trees growing up through them. I was holding back on cutting them down because they were great trees and was hoping someone would want them.

In the end I couldn't find anyone that wanted them so I started trimming the hedge with the intention of taking all the trees down. Once again I forgot to take a before picture but here is an in progress one.

The area inside the hedge is a small garden with Azaleas, Nandinas, and Camellias. It is also overgrown with weeds, small treess, and poison ivy everywhere. I cleared this area out once back in 2008, you can see what it looked like then here.

As I worked on it my wife and I got to talking about a picket fence for the front yard. we've talked about one before but never followed through. This time we decided to go price out the wood. After pricing the wood we decided to go ahead and do it.

The first step was to layout the fence line, I used chicken wire fence stakes and string. Then I spray painted a dot every 6 feet along the line for fence posts.

Next came the fun part, digging 45 fence post holes by hand. With the holes dug I installed the posts and concreted them in making sure they were perfectly level all the way around and in a perfectly straight line.

Next came the cross pieces and then finally the pickets. I had to make a jig for my miter saw to cut the points on all the pickets, all 500 of them. In the picture below you can see the jig with a fence picket in it ready to be cut. I ended up doing 2 at a time which sped up the process. I used the same jig in a different position to cut down half of the posts 2" since the fence will have alternating height pickets.

I created a picket with blocks on to get the proper spacing between pickets. For the first fence section I had to lay the pickets out in front of the fence to get the proper spacing. Once I knew how many pickets would fit in a given amount of space I used that to figure out how far in to start the first picket on each section.

In the above picture you can see my spacer picket, I clamped it in place so my hands were free to screw the next picket into place. In the subsequent sections I also clamped a 2x4 to the bottom board to get the bottom of the pickets at the correct height easily.

The fence has 3 gates, a double gate at the front and one on either side near the back of the fence.

 Front gates

 North side gate

South side gate

Anyone see anything wrong with the two side gates?

The north side gate goes to the neighbors yard, which just so happens to be my mother. The south side gate goes to the driveway, there is a drop-off here so I will build a couple of brick steps here.

Once I finished the fence I got back to work on the hedge and removed all the weeds, trees, and sprayed the poison ivy.

Here are some pictures of the completed fence (and boxwood hedge).

The corner posts and the side gate posts have decorative caps on them, the main gate posts have decorative caps with a ball on top, and the rest of the posts are beveled at the top.

The jury is still out on whether to paint the fence white or just use a sealer on it. I think painting it white (our trim color on the house) would look the best but I'm not looking forward to the upkeep.

Here's a before and after of the north side of the house and yard. The before was taken in Sep 2007 a few months before we bought the house.

Main Bathroom Update

The main bathroom is another project that I have been working on. Last week I finished cutting in the primer on the walls, then I scraped all the trim.

One of the neat things I found here was the old exterior trim color, it's the brown/olive looking color on the door casing. This room used to be a side porch. I know this was an exterior color because when they closed the porch in and hung the interior door they just slapped the hinges up on the casing, you can see where they were on the casing on the right. That color was directly underneath.

Once the scraping was done I primered and painted all the trim, then painted the walls.

Sorry for the pics, it's very hard to get decent shots in this room.

Left to do still is install 1/4 round and baseboards, caulk, and paint the ceiling.

Oak Tree Removal

There are two very large Oak trees in front of our house. I'm pretty sure they are as old as the house. There used to be three but one was hit by lightning years ago and came down. I removed the stump from that one last year with the help of a friend and his back hoe. The root ball was over 6 feet in diameter and lifted the front wheels of the tractor 4 feet off the ground when we picked it up with the back hoe arm.

The next tree over (the one that would have originally been in the middle of the three)  was starting to look really bad, there is a large rot hole at the top of the trunk where a large limb had fallen off many years ago. It's been getting steadily larger over time.

I've become increasingly concerned that the tree will come down on the house in a storm so I spoke with the city about taking it down as it's in the right-of-way on their property. The city council voted to have an arborist come out and make an assessment of the tree and go ahead and take it down if that's what the arborist recommended.

The arborist came out and immediately recommended that the tree come down. The city got the tree removal service out a few days later.

Look at that trunk, almost all heart. Too bad I dont have a sawmill handy.

They had to cut the trunk in half because it was too heavy for their crane to pick up.

I hate to see the tree go but it was becoming too much of a danger to the house and us.

Finishing the brick walkway

After spreading sand over the bricks and waiting two days for a vibrating sled compactor to become available I finally went ahead and raked and swept the sand down in the cracks as best I could. As it settles I will add sand to the cracks.

I should have swept the rest of the sand off the bricks before taking these pictures but I didn't.

I will eventually run the walk all the way out to the sidewalk.